Browse
Categories

Placing a Gate in a Terrain Wall

Reference Number: KB-00874 Last Updated: 12-12-2014 01:20 PM

The information in this article applies to:

Chief Architect Premier or Chief Architect Interiors or Chief Architect Lite

QUESTION


I have placed a ­terrain wall in my design, but can't seem to add a gate do it.  How do I do that?



ANSWER




While in many ways a Terrain Wall acts like a fence and follows the contours of the terrain features, regions, and elevation lines that you have placed, it does not act like a fence in that you cannot place a gate directly into a Terrain Wall.

In this tutorial we will walk through creating a Terrain wall and then placing a gate with columns on either side of it.

To place a Terrain Wall


Creating a stone wall that follows your terrain is easy using the Terrain Wall  tools.

  1. First, launch your Chief Architect software and select File> Open Plan , browse to the location of the plan in which you want to add your stone wall and open it.

  2. Select Terrain> Walls and Curbs> Straight Terrain Wall then click and drag in your plan to create two sections of your wall with a gap between them, we will place the gate in this gap later. In this example a gap of 9' (108") is used.

    Note: Recall that like other line-based objects, if you want to change a straight section of your Terrain Wall into a curved section, you use the Change Line/Arc  tool to do this. You can also place breaks into your terrain wall using the Break Line edit tool in order to create additional points at which to change the terrain wall after it has been placed.


  3. Notice that, by default, ­concrete is used as the material for our terrain wall. To change this to a stone material, use the Select Objects tool to select the terrain wall and click on the Open Object edit tool to display its specification dialog.

    • On the General panel, we will first increase the thickness of our terrain wall by changing its Width from the default value of 6" to 15".

    • Also, for the purposes of this example, we will lower its Height from the default value of 60" down to 36".

  4. Now, select the Materials panel and click on the Terrain Path then click the Library Material button to display the Select Library Object dialog.

  5. You can click on the  to expand out the Materials or Manufacturers libraries and browse to the location of the type of material that you want to use.

    For the purposes of this example, we used the Cambria stone material located in the Manufacturers catalog in Eldorado Stone.

    To download the Eldorado Stone products and other bonus manufacturer content, on the Chief Architect website select Library> Get additional Content Online  from the menu.


  6. Once you have selected the appropriate material, click the OK button to close out of the Select Library Object dialog.

  7. Click OK again to apply the material and close out of the Terrain Wall specification dialog.


  8. Repeat these steps for the other section of wall.

    To place a gate in a Terrain Wall

    In many ways Terrain Walls act like fences; they follow the contours of the terrain features, regions, and elevation lines that you have placed. However, unlike a fence, you cannot place a gate directly into a Terrain Wall.  




    In this section of the tutorial, we will show you how to connect a section of fence to the terrain wall to place a gate.

    1. Select Build> Fencing> Straight Fencing and click and drag a fence segment in between the two Terrain walls.


    2. Select Build> Door> Hinged Door and click in the newly placed fence to place an opening in it.


    3. Using the Select Objects tool, select the door and click on the Open Object edit tool to display the Door Specification dialog.


    4. On the General panel, click the Library button to display the Select Library Object dialog and browse to Architectural>Fences & Railings> Gates.

      For the purposes of this example, we selected the Wrought Iron Gate (arched).
       

    5. Next, set the Width to be 65" so that a double gate is created and increase its Thickness to be 4" and click the OK button to apply these changes.


    6. Using the Select Objects tool, click on the fence segment and click on the Open Object edit button to display the Fencing Specification dialog.


    7. On the General panel, change the Thickness of the fencing to be 21".

      We want the thickness of the Fencing to be greater than that of the Terrain walls to allow for the appearance of larger square columns on either side of the gate.


    8. On the Newels/­Balusters panel, increase the Newel Height from its default value of 42" to 48" and the Newel Width to 21" and notice that the preview image in the dialog updates to show this change. Also uncheck Default and Draw Newels/Balusters.


    9. On the Railing panel check No Rail.


    10. On the Materials panel, set the Newel's materials to be the same as that which we used for the Terrain Walls, which was Cambria.


    11. Once you have completed these changes, click the OK button to apply them and close the Fencing Specification dialog.

    The image below demonstrates what the 2D Floor plan view of the terrain walls, fence and gate should look like.


    To place a cap on top of the Fencing columns as shown in the image of the gate, you can use the rectangular Geometric Shape out of the Library Browser, apply the same stone material, and resize and place it appropriately over the colums.


      MORE INFORMATION


      To download a catalog of bonus Eldorado Stone textures and other bonus libraries, visit our Online 3D Library.